49 results for your search "Problems & solutions - Waterproofing / Mortars"
There are several reasons for humidity damages. In this application tip, we look at how the humidity damage can be detected
The right determination of actual water level is most important for the planning of water-proofing works and the choice of the waterproofing system. This application tip shows you how to determine…
The concept of waterproofing is based on the results of in-situ checks and laboratory tests with comprehensive key parameters. This application tip goes into the necessary planning steps for…
This application tip describes which investigation methods should be carried out before basement renovations and what should be considered
The renovation works of old waterproofing need a careful evaluation of the substrate, since it must be matched with several types of substrates and old waterproofing materials. This application tip…
Waterproofing products of building structures must do a lot. Watertightness, long-life expectancy, flexibility, and resistance to weather conditions – all these requirements must be fulfilled by…
In this application tip we show you how to repair old waterproofing without removing the old bitumen paint or coating. This is possible due to the patented Weber system "Renovation system for old…
Weber bitumen thick-layer coatings and reactive sealants can be used to seal a variety of substrates safely, permanently and easily. The substrates in this application tip have proven themselves in…
A well-done waterproofing can be only as good as the substrate will allow. Therefore, the substrate must be carefully checked before the waterproofing is applied. This application tip addresses how…
When working underwater pressure, joints, break-outs and cracks can occur. This application tip shows you how to seal these easily and safely with Weber's fast-setting mortars.
One of the most important investigations prior to renovation work is to record the type, thickness and properties of the existing masonry. This application tip shows you how to do this step by step
The requirements for thermal insulation and the living climate, also in basements or especially in basement living spaces, are higher than ever before. This application tip describes the process of…
Particularly during cool and humid months, the influence of weather conditions on the waterproofing material and the concerned building parts must be taken into consideration. This application tip…
Whenever using brush-, trowel- or spray-grade cement-based or bitumen-based waterproofing materials, the total layer thickness must be checked in order to guarantee their watertight efficiency. This…
Great care is a "must" for structural wall joints separating buildings and for dilatation joints in case of external basement waterproofing. This application tip shows how to minimize the challenge…
Cold- and self-bonding bitumen membranes fulfill the standards for the water impact classes W1-E "ground damp" and "non-pressure water" (DIN 18533). This application tip addresses how to waterproof a…
For a performing waterproofing of in-situ concrete or prefabricated concrete elements, the waterproofing between the concrete elements as well as between concrete slab and concrete elements is most…
This application tip explaines how to use polymer-modified bitumen thick coatings for waterproofing works.
The performance of "flexible waterproofing slurries" is obvious. Due to their flexibility, they are able to bridge cracks of building parts to a limited extent.
The waterproofing must be all of a piece, if the critical facade socket part and the groove area (angle between concrete slab and basement wall) below ground level of buildings are to be permanently…
Post-applied interior waterproofing in combination with the interior mineral wall insulation boards weber.therm MD 042 Dämmboard innen offers optimum moisture and heat protection, saves valuable…
The product systems presented here offer the contractor different application alternatives, especially for concreting or levelling and repair works.
Balconies, terraces and walkways are subject to extreme requirements, such as frost, heat and mechanical loads. With 1- or 2-component balcony coatings based on polyurethane resin, these building…
Depending on the type of facade, waterproofing of the socket area can be carried out by using reactive waterproofing coatings, flexible cement-based waterproofing coatings or bitumen thick-layer…
Liquid resins as waterproofing and waterproofing systems score points, in particular for their durability and low maintenance requirements
weber.san 958 is a quick-setting, multi-use white damp-proof render/plaster for the sustainable repair of moist and salt-contaminated surfaces. The mineral render with WTA certificate facilitates the…
The internal masonry socket part is precisely the area where different building materials meet together, and the highest humidity impact will often exist. The renovation of this part of the building…
Due to the growing interest in the preservation of valuable building substance, the importance of renovation of basement rooms is constantly growing. A prior inventory and an analysis of the damages…
This application tip describes the relevant steps when renovating damp damages in brickwork or renders/plasters with the Weber system "Easy and safe renovation of damp masonries".
Damp-proof renders/plasters contribute to a better indoor climate by absorbing moisture. This application tip explains the benefits and application of these plasters
A lot of drinking water and service water tanks in towns and municipalities show age-related defects. This application tip describes the renovation of water tanks with products that meet all hygienic…
Bitumen roof surfaces are always and constantly exposed to weather conditions. Bitumen materials are therefore subject to high stress in the long term. This application tip shows how you can easily…
Exterior walls with mineral building materials must have a high water-repellent effect in order to prevent mould growth and moisture on the inner side of the building. This application tip descripes…
The new pot life retarder weber flextime ensures relaxed working times (pot life) of up to 90 minutes in summer for reactive waterproofing compounds and tile adhesives despite +30 °C.
In basement rooms, damp, uneven and leaky floors are often found instead of the desired storage space.Conventional solutions are usually very costly. They involve many work steps and are above…
Epoxy and polyurethane resins are supplied in two matched components and are brought to reaction by intensive mixing.